Final drive bolt hole cover wanted.

Looking for Aftermarket parts and Accessories for your BMW R1200RT/R1250RT or found something useful you want to share? Or just a general question?
Post Reply
Toddy
Posts: 13
Joined: Tue Aug 14, 2018 11:17 am
Location: Renfrewshire
Bike Model and Year: 2019 R1250RT
Been liked: 1 time
Ireland

Final drive bolt hole cover wanted.

Post by Toddy »

Hiya, the final drive on my 2014 RTLC has two exposed bolt holes, used to support the flappy mudguard thing on a GS. I'm wondering if anyone has seen a cover for these?
Have searched the Touratech and Wunderlich sites but no luck.
Something to smarten it up.
Attachments
IMG_20180817_091112.jpg
User avatar
Levisp
Posts: 1114
Joined: Sun Aug 31, 2014 12:57 pm
Been liked: 1 time

Re: Final drive bolt hole cover wanted.

Post by Levisp »

I just used some bolts. Sorry cannot remember the size.
Attachments
IMG_0242.jpg
Toddy
Posts: 13
Joined: Tue Aug 14, 2018 11:17 am
Location: Renfrewshire
Bike Model and Year: 2019 R1250RT
Been liked: 1 time
Ireland

Re: Final drive bolt hole cover wanted.

Post by Toddy »

Thanks, good simple solution and looks better than I thought.
User avatar
BeeJay
Posts: 299
Joined: Fri Jan 30, 2015 8:52 pm

Re: Final drive bolt hole cover wanted.

Post by BeeJay »

M6 machine screw will fit. I tried a 20mm screw and it looked like I need to cut 10mm off.
So if you can get a 10mm bolt then that should be spot on.
Just need to find a black couple for my bike.
Or a spot of paint,
RTs4me
Subscriber
Posts: 113
Joined: Sun Mar 08, 2015 10:42 am
Has liked: 6 times
Been liked: 15 times
Great Britain

Re: Final drive bolt hole cover wanted.

Post by RTs4me »

My new RT has the black engine/shaft housing/bevel box.
I cleaned the bright machined areas of the bevel box with paint prep wipes, to remove any grease etc, then painted with Halfords Satin Black. Then to fill the holes up, I fitted some stainless Allen bolts with stainless washers. Looks good! :)
My aim was to create a continuous painted surface. I think that the raw edges where the machined-out areas meet the paint is where the moisture creeps in and starts to lift the paint. :(
Last edited by RTs4me on Tue Aug 21, 2018 4:06 pm, edited 1 time in total.
User avatar
David.
Subscriber
Posts: 8342
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 395 times
Great Britain

Re: Final drive bolt hole cover wanted.

Post by David. »

Last edited by David. on Tue Aug 21, 2018 4:25 pm, edited 1 time in total.
CarbonB55
Posts: 4
Joined: Tue Aug 21, 2018 12:21 am

Re: Final drive bolt hole cover wanted.

Post by CarbonB55 »

I put stainless hex head bolts in mine ( 2016 ) new to me .[attach=1]
Attachments
20180821_201141_HDR.jpg
Toddy
Posts: 13
Joined: Tue Aug 14, 2018 11:17 am
Location: Renfrewshire
Bike Model and Year: 2019 R1250RT
Been liked: 1 time
Ireland

Re: Final drive bolt hole cover wanted.

Post by Toddy »

Thanks David, I ordered two bolts and two washers, total bill £1.92 including carriage, hope they don't mind. Great source for bits.
😁
User avatar
David.
Subscriber
Posts: 8342
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 395 times
Great Britain

Re: Final drive bolt hole cover wanted.

Post by David. »

Toddy wrote:I ordered two bolts and two washers, hope they don't mind. Great source for bits.
Are three screws & washers required, RealOEM shows three for the GS rear mudguard, https://www.realoem.com/bmw/enUS/showpa ... Id=46_1486

Mark at Stig Fasteners is spot on & small orders are fine, he lives locally to me, I can collect, therefore no P&P.
Last edited by David. on Wed Aug 22, 2018 7:04 am, edited 1 time in total.
Toddy
Posts: 13
Joined: Tue Aug 14, 2018 11:17 am
Location: Renfrewshire
Bike Model and Year: 2019 R1250RT
Been liked: 1 time
Ireland

Re: Final drive bolt hole cover wanted.

Post by Toddy »

Dohhhh!, Yes, thanks, must cut one.
JC-RT
Posts: 25
Joined: Sat Aug 04, 2018 11:27 pm

Re: Final drive bolt hole cover wanted.

Post by JC-RT »

I went with stainless steel hex button screws M6x1.0x10mm . I also used stainless steel washers.
I had to purchase a bag of ten screws so I have some extras available. I have 2 sets of three bolts if interested for  $1.00 plus shipping for three screws (no washers - not mandatory).
Attachments
20181102_203625_resized.jpg
Last edited by JC-RT on Sat Nov 03, 2018 10:44 am, edited 1 time in total.
User avatar
David.
Subscriber
Posts: 8342
Joined: Fri Nov 07, 2014 7:29 pm
Location: North Yorkshire
Bike Model and Year: R1200RT (Camhead) 2012
Been liked: 395 times
Great Britain

Re: Final drive bolt hole cover wanted.

Post by David. »

Stig Fasteners now do an M6 x 10 Torx Flange Button Screw, https://www.a2stainless.co.uk/M6-x-10-T ... AZP1A.aspx

A BMW style Torx screw that doesn't require a washer, looks neat.

Image
Post Reply