Hi forum, first post
I've had this R1200 (2015 R1200RT) for a few weeks now and I'm having much fun. Having been lurking on here for a while, I have read a few posts about the notorious rusting driveshaft so wanted to see what mine was like.
It looks like crap!
I'm worried now. Do I stop riding? Do I buy a new one (or a decent looking spare), or should I try and follow one of the YT guides and get some wire brush on it?
I expect I could take it apart and check if its notty or has some play, but if it looks beyond repair, I'll just prefer to get ordering a new one.
I was always planning on dealing with the bits of bubbling rust around the edges, I didn't even know you could pull this back and look into it.
Is this driveshaft salvagable?
-
- Posts: 2
- Joined: Sun Apr 23, 2023 6:02 pm
- Location: Nuneaton, UK
- Bike Model and Year: 2015 R1200RT
- Randyjaco
- Posts: 225
- Joined: Thu Nov 11, 2021 3:18 am
- Location: Friendswood, Texas, USA
- Bike Model and Year: R1200RT 2017
- Has liked: 53 times
- Been liked: 46 times
Re: Is this driveshaft salvagable?
I would remove the shaft and see if you have any binding in the universal joints. If they are smooth, you are good to go. I would put some spline lube on the splines and reassemble.
The U-joint bearings are factory sealed, so there is nothing to be done on them, unless they are binding. If they are, you are going to be investing on a new driveshaft. The surface rust on the shaft is no big deal, but you could wire brush it and paint with a rattle can.
When you remove the shaft, take care that the rear splines separate first. Reconnecting the front splines is a little fiddley. A steel welding rod can be formed to help support the front U-joint to better align the splines.
The U-joint bearings are factory sealed, so there is nothing to be done on them, unless they are binding. If they are, you are going to be investing on a new driveshaft. The surface rust on the shaft is no big deal, but you could wire brush it and paint with a rattle can.
When you remove the shaft, take care that the rear splines separate first. Reconnecting the front splines is a little fiddley. A steel welding rod can be formed to help support the front U-joint to better align the splines.
-
- Posts: 2
- Joined: Sun Apr 23, 2023 6:02 pm
- Location: Nuneaton, UK
- Bike Model and Year: 2015 R1200RT
- Doctor T
- Posts: 1998
- Joined: Tue Dec 21, 2021 10:21 pm
- Location: west sussex
- Bike Model and Year: 2007 R1200RT SE
- Has liked: 1152 times
- Been liked: 306 times
Re: Is this driveshaft salvagable?
Drag it out and inspect it. If it feels smooth on all axis and no play, you are OK. Grease up the splines and the UJ's.
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
"Blessed are the cracked, for they shall let in the light". Groucho Marx
"Blessed are the cracked, for they shall let in the light". Groucho Marx
-
- Posts: 38
- Joined: Tue Sep 02, 2014 9:31 pm
- Location: Somewhere else
- Has liked: 5 times
- Been liked: 8 times
Re: Is this driveshaft salvagable?
Sorry mate but its knackered.The rust has probably siezed it to the final drive.It has cetainly compromised the seals for the yoke bearings and the bearings will fail soon with catastrophic results ( shaft through casing, rear wheel lock up). Needs a new shaft minimum. The sad thing is, if it was a GS, the snivelling scroats at BMW would cover it in their current "service measure"