Bike turner

General discussion of the BMW R1200RT/R1250RT
Post Reply
lancashirert
Posts: 82
Joined: Thu Aug 15, 2024 7:11 pm
Bike Model and Year: R1200RT LE 2018
Has liked: 39 times
Been liked: 20 times
Great Britain

Bike turner

Post by lancashirert »

Moving house soon, and will have a garage down the side of the house which is an incline and also only the width of the garage.

Any suggestions and recommendations for turners? Seen you can get centre stand ones, and also the type which you ride the bike on to and then you can wheel it round the garage. Not aware of any other ideas offhand, although the daughter’s flyweight Vespa suddenly looks more appealing to put away than a 1/4 ton bike :lol:

Cheers!
burridge01
Posts: 806
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: NUFFINK
Been liked: 327 times
Great Britain

Re: Bike turner

Post by burridge01 »

I have the centre stand jobby,OK in the garage,wouldn't chance it on an incline for fear of rolling off.I had one of the long ones you pop the bike on then on to its side stand,maneuverability is nowhere near as good as the centre stand one(in my opinion)and again,maybe an issue on an incline.

A possible alternative is the rear wheel lift(like they use in paddocks)grips the tyre/wheel and allows you to spin the bike round on the spot,maybe the best solution but probably the most expensive.
lancashirert
Posts: 82
Joined: Thu Aug 15, 2024 7:11 pm
Bike Model and Year: R1200RT LE 2018
Has liked: 39 times
Been liked: 20 times
Great Britain

Re: Bike turner

Post by lancashirert »

I definitely have no intention of turning it on the incline! Just to turn it in the garage really.

Could look at rear wheel lifting. Have a wheeled paddock stand still…. Shall have a look at a centre stand turner though, thanks.
Arends
Posts: 44
Joined: Sat Mar 16, 2024 8:21 pm
Location: Ireland
Bike Model and Year: BMW R1200RT 2015
Has liked: 39 times
Been liked: 7 times
Ireland

Re: Bike turner

Post by Arends »

I've seen on YT a lazy Suzan mechanism/bearings mounted on two sheets of plywood, but the user had lighter bike.
I am here to learn.
User avatar
Glenn
Subscriber
Posts: 393
Joined: Sat Jan 15, 2022 7:49 pm
Location: Shropshire
Bike Model and Year: R1250RT LE 2019
Has liked: 43 times
Been liked: 146 times
Great Britain

Re: Bike turner

Post by Glenn »

I use a 50cm version of this
lancashirert
Posts: 82
Joined: Thu Aug 15, 2024 7:11 pm
Bike Model and Year: R1200RT LE 2018
Has liked: 39 times
Been liked: 20 times
Great Britain

Re: Bike turner

Post by lancashirert »

Glenn wrote: Mon Oct 07, 2024 7:20 am I use a 50cm version of this
That's neat, will search as out of stock on his link.

Found this type last night: https://www.amazon.co.uk/gp/product/B0D ... ct_title_2 - which might allow a little shunting too.
burridge01
Posts: 806
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: NUFFINK
Been liked: 327 times
Great Britain

Re: Bike turner

Post by burridge01 »

That's similar to what I use
Image
That was a mighty bike :lol:

Takes the weight of the RT no problem.If you go down that route,make sure the floor is fairly smooth :thumb:
lancashirert
Posts: 82
Joined: Thu Aug 15, 2024 7:11 pm
Bike Model and Year: R1200RT LE 2018
Has liked: 39 times
Been liked: 20 times
Great Britain

Re: Bike turner

Post by lancashirert »

burridge01 wrote: Mon Oct 07, 2024 1:52 pm That's similar to what I use
Image
That was a mighty bike :lol:

Takes the weight of the RT no problem.If you go down that route,make sure the floor is fairly smooth :thumb:
This is the conundrum, I can’t remember the garage floor! And I need it the day I move, or rather the next day I want the bike out!
User avatar
Doctor T
Posts: 1998
Joined: Tue Dec 21, 2021 10:21 pm
Location: west sussex
Bike Model and Year: 2007 R1200RT SE
Has liked: 1152 times
Been liked: 306 times
Great Britain

Re: Bike turner

Post by Doctor T »

I have the same as above. I have an uneven bumpy floor in my garage and it works well. Think I paid about £35 delivered from Ebay.
Trust me I am a retired Doctor and lecturer at Oxford University of Structural and Mechanical/Electrical engineering.
"Blessed are the cracked, for they shall let in the light". Groucho Marx
burridge01
Posts: 806
Joined: Tue Jul 02, 2019 11:25 am
Location: Basildon, Essex
Bike Model and Year: NUFFINK
Been liked: 327 times
Great Britain

Re: Bike turner

Post by burridge01 »

Doctor T wrote: Tue Oct 08, 2024 12:50 pm I have the same as above. I have an uneven bumpy floor in my garage and it works well. Think I paid about £35 delivered from Ebay.
Mine did move but it was to erratic, so I got some filler gear of a job I was on and after filling said holes it was all a lot smother :thumb:
Post Reply