GS1250 top yoke, can be used for RT bar conversion

Got a BMW R1200RT/R1250RT for sale? selling some accessories?
User avatar
fresh
Posts: 12
Joined: Sun Sep 01, 2024 4:38 pm
Bike Model and Year: R1200RT 2015
Has liked: 3 times
Been liked: 6 times
United States of America

Re: GS1250 top yoke, can be used for RT bar conversion

Post by fresh »

Panman40 wrote: Fri Oct 25, 2024 5:51 pm I only got this far before deciding to just use the RT original bars.
That's the clearest pic I've seen so far of the setup. Thank you so much! :cheers:

So to me, that setup looks higher and maybe 3/4 of a fist wider. Did you find it was too wide for you, or too high, etc.?
Panman40
Subscriber
Posts: 490
Joined: Tue Mar 22, 2022 8:46 pm
Has liked: 478 times
Been liked: 79 times
Great Britain

Re: GS1250 top yoke, can be used for RT bar conversion

Post by Panman40 »

fresh wrote: Fri Oct 25, 2024 6:01 pm That's the clearest pic I've seen so far of the setup. Thank you so much! :cheers:

So to me, that setup looks higher and maybe 3/4 of a fist wider. Did you find it was too wide for you, or too high, etc.?
No problem, I think the width was 3” wider each side, it felt quite good for me, iI found that the used bars I bought had a very slight bend from a drop on the right side so I would of needed to find another set, I got a refund ok. Also to get a test ride in I woukd if needed to drill out the 2 ignition switch bolts , not a hard job and I even bought 2 new security bolts and the little tool to install them from bmw for not much money but I just decided not to bother.
Panman40
Subscriber
Posts: 490
Joined: Tue Mar 22, 2022 8:46 pm
Has liked: 478 times
Been liked: 79 times
Great Britain

Re: GS1250 top yoke, can be used for RT bar conversion

Post by Panman40 »

fresh wrote: Fri Oct 25, 2024 6:01 pm That's the clearest pic I've seen so far of the setup. Thank you so much! :cheers:

So to me, that setup looks higher and maybe 3/4 of a fist wider. Did you find it was too wide for you, or too high, etc.?
If you look at the first page part way down you will see Easyriders images fairly clearly 👌
User avatar
fresh
Posts: 12
Joined: Sun Sep 01, 2024 4:38 pm
Bike Model and Year: R1200RT 2015
Has liked: 3 times
Been liked: 6 times
United States of America

Re: GS1250 top yoke, can be used for RT bar conversion

Post by fresh »

Panman40 wrote: Sat Oct 26, 2024 3:14 am If you look at the first page part way down you will see Easyriders images fairly clearly 👌
I finally found the thread on it, which has lots of good pictures, by just trawling through their posts:
GS Top Yoke Conversion Kit

Sorry if I was a bother here. Just really trying to sort out a potentially big decision. Thanks again for the details provided and help.
Panman40
Subscriber
Posts: 490
Joined: Tue Mar 22, 2022 8:46 pm
Has liked: 478 times
Been liked: 79 times
Great Britain

Re: GS1250 top yoke, can be used for RT bar conversion

Post by Panman40 »

fresh wrote: Sat Oct 26, 2024 4:57 am I finally found the thread on it, which has lots of good pictures, by just trawling through their posts:
GS Top Yoke Conversion Kit

Sorry if I was a bother here. Just really trying to sort out a potentially big decision. Thanks again for the details provided and help.
No bother lol!, sorry I thought I was already in that thread :lol: , hopefully you can make a decision, I regret not changing the ignition switch over and giving it a go, no doubt I would have if the bars were dead straight.
User avatar
fresh
Posts: 12
Joined: Sun Sep 01, 2024 4:38 pm
Bike Model and Year: R1200RT 2015
Has liked: 3 times
Been liked: 6 times
United States of America

Re: GS1250 top yoke, can be used for RT bar conversion

Post by fresh »

I saw that Renthal makes GS bars, and they're obviously much cheaper to aquire than BMW's. I was thinking about buying a set just to see what the actual geometry was like in real life, right up next to the stock bars. But that could also be a less expensive way for you to get some new straight bars.

Renthal 835-50 STREET FATBAR BMW R GS/GSA AC ($106.45)
User avatar
EasyRider
Subscriber
Posts: 938
Joined: Tue Nov 21, 2023 7:27 am
Location: Wales
Bike Model and Year: 2019 R1250RT LE
Has liked: 121 times
Been liked: 305 times
Wales

Re: GS1250 top yoke, can be used for RT bar conversion

Post by EasyRider »

All i can say, is i will never go back to the stock handlebars. I really like having the GS conversion on Artie.
With the GS bars, the lower footpegs and the sargent seat fitted, has for me made the RT a really nice bike to ride.
Dont Ride Faster, Than Your Angel Can Fly. :thumb:
MotoGary
Posts: 1
Joined: Thu Oct 31, 2024 4:28 pm
Bike Model and Year: R1250RT
Has liked: 1 time
United States of America

Re: GS1250 top yoke, can be used for RT bar conversion

Post by MotoGary »

Hi Guys, I joined the forum today specifically because of a question on the GS handlebar conversion. I'm looking at buying a 2022 RT from a non BMW dealer. When I saw the bike, it did not have the normal RT handlebar setup I expected. It looked like some aftermarket conversion, which concerned me. When I asked the dealer about it, they said that the previous owner was military and bought the bike in Germany and shipped it over here when he came back. They said that the previous owner said the bars were stock (which I doubted). So my research lead me to this post.

From reading here, it appears possible that he could have ordered the GS bar setup from that factory, is that correct? The dealer does not have the original RT yoke or bars, so my next question is: Anyone know how much it would cost to convert back to the stock RT configuration?

I've previously owned a 1200RT and both 1150 and 1200 GS, so I'm familiar with the RT and GS. I'm not necessarily opposed to the GS bars on the RT, but I'm thinking down the road when it comes time to sell. The GS bars may be a little off-putting for some, so I'm trying to determine what it might take to put it back to stock RT.

Here are pics. It looks like it's probably the factory installed GS setup with the addition of owner installed risers. Does that seem correct?
Attachments
IMG_6724.jpg
IMG_6724.jpg (146.82 KiB) Viewed 721 times
IMG_6723.jpg
IMG_6723.jpg (184.11 KiB) Viewed 721 times
Last edited by MotoGary on Fri Nov 01, 2024 11:42 pm, edited 6 times in total.
User avatar
Glenn
Subscriber
Posts: 386
Joined: Sat Jan 15, 2022 7:49 pm
Location: Shropshire
Bike Model and Year: R1250RT LE 2019
Has liked: 43 times
Been liked: 144 times
Great Britain

Re: GS1250 top yoke, can be used for RT bar conversion

Post by Glenn »

Add the picture as an attachment, it should display fine.

You may find @EasyRider has the original bars for sale, but it could be expensive the ship the the US
simbo
Subscriber
Posts: 1465
Joined: Fri Sep 16, 2016 10:33 pm
Location: Greater Manchester
Bike Model and Year: RT 2011
Has liked: 80 times
Been liked: 144 times
Great Britain

Re: GS1250 top yoke, can be used for RT bar conversion

Post by simbo »

MotoGary wrote: Thu Oct 31, 2024 6:04 pm Here are pics. It looks like it's probably the factory installed GS setup with the addition of owner installed risers. Does that seem correct?

Yes, going from the pictures that looks like an OEM GS bar set up with additional aftermarket bar risers.
The GS 'is' the better bike :-)
User avatar
fresh
Posts: 12
Joined: Sun Sep 01, 2024 4:38 pm
Bike Model and Year: R1200RT 2015
Has liked: 3 times
Been liked: 6 times
United States of America

Re: GS1250 top yoke, can be used for RT bar conversion

Post by fresh »

I had missed the discussion replies, but I did find a very nice walkaround video of a stock RT with the tubular bar option:
2022 BMW R1250RT R1250 RT R 1250 Premium Sport

Right now, I'm leaning heavily towards finding a 2024 with this setup. There's a couple on the west coast right now. I'm still guessing that BMW is going to announce a new 1300 RT, later at EICMA. They've mostly announced updates to their sport bikes so far there.
Mart UK
Posts: 6
Joined: Thu Nov 07, 2024 9:54 am
Bike Model and Year: R1250RT 2024
Has liked: 1 time
Been liked: 3 times
Great Britain

Re: GS1250 top yoke, can be used for RT bar conversion

Post by Mart UK »

I bought a 2024 RT 2 weeks ago. I think BMW may have ended production of the 1250RT. I got the impression, at least here in the UK, the dealer only had a choice of what has already been produced and they are swapping unregistered stock between different dealership chains, to meet a customer's order. Exactly what I wanted was available. The handlebar option may be more difficult to find, though.
User avatar
fresh
Posts: 12
Joined: Sun Sep 01, 2024 4:38 pm
Bike Model and Year: R1200RT 2015
Has liked: 3 times
Been liked: 6 times
United States of America

Re: GS1250 top yoke, can be used for RT bar conversion

Post by fresh »

Congrats on the new wheels! :)

They're playing it right - I can't figure out what they're going to do. It looks like they still had the 1250 on display at EICMA:
EICMA 2024: BMW F450GS 4K

I'm wondering what a dealer would say if I asked to order a 2025.
Post Reply