Page 2 of 3

Re: Auxiliary light brackets

Posted: Thu May 11, 2023 9:06 pm
by Stu
Discovered tonight that the lights are too close to the floor when going round corners!

Back to the drawing board before I scrape one on the deck

Re: Auxiliary light brackets

Posted: Thu May 11, 2023 9:46 pm
by Panman40
sakm wrote: Thu May 11, 2023 9:06 pm Discovered tonight that the lights are too close to the floor when going round corners!

Back to the drawing board before I scrape one on the deck
That’s annoying!, I can’t remember the last time I rode in the dark…🤔🤣

Re: Auxiliary light brackets

Posted: Thu May 11, 2023 10:34 pm
by Stu
Panman40 wrote: Thu May 11, 2023 9:46 pm That’s annoying!, I can’t remember the last time I rode in the dark…🤔🤣
They don't get lower when I turn them on 😂

A mate was following me and said they was about an inch off the floor and we was only going steady 😳

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 3:44 pm
by Doctor T
Have you any pictures Stu

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 3:59 pm
by Stu
Doctor T wrote: Fri May 12, 2023 3:44 pm Have you any pictures Stu
There's some on page 1

None of them almost on the floor though 😂

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 4:18 pm
by Doctor T
I know it may weaken the bars but cant you drill a hole in the top section to receive a small sleeve and drop the spot lamp bolt through it? You could weld the sleeve in the hole for added strength.
If this doesn't work How about welding a steel bar to the top section for a spot mount? Sprayed with satin matt paint to cover the welds.

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 4:23 pm
by Stu
Doctor T wrote: Fri May 12, 2023 4:18 pm I know it may weaken the bars but cant you drill a hole in the top section to receive a small sleeve and drop the spot lamp bolt through it? You could weld the sleeve in the hole for added strength.
If this doesn't work How about welding a steel bar to the top section for a spot mount? Sprayed with satin matt paint to cover the welds.
The bars are too close to the engine to allow the spots to sit there.

The mounts I have protrude forwards but it's still not enough!

I am going to have a look and see if I can tuck them in a bit more

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 4:34 pm
by Doctor T
can you take a sideways pic. So i can see if i can make or come up with a solution for you

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 6:13 pm
by burridge01
sakm wrote: Fri May 12, 2023 4:23 pm The bars are too close to the engine to allow the spots to sit there.

The mounts I have protrude forwards but it's still not enough!

I am going to have a look and see if I can tuck them in a bit more
You will eventually succumb to Denali :thumb:

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 6:41 pm
by Stu
Doctor T wrote: Fri May 12, 2023 4:34 pm can you take a sideways pic. So i can see if i can make or come up with a solution for you
Thanks for the offer but I'm not adverse to a bit of fabrication if needed but I don't want to start welding stuff on to new bars and then having to get them powder coated again!

I have the perfect solution sat on the bench in the shape of the stock light mounts but as I say I don't want to weld them on

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 6:42 pm
by Stu
burridge01 wrote: Fri May 12, 2023 6:13 pm You will eventually succumb to Denali :thumb:
Never 😂

Although I might order the mounts take some measurements and send em back 😂

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 6:50 pm
by Doctor T
sakm wrote: Fri May 12, 2023 6:41 pm Thanks for the offer but I'm not adverse to a bit of fabrication if needed but I don't want to start welding stuff on to new bars and then having to get them powder coated again!

I have the perfect solution sat on the bench in the shape of the stock light mounts but as I say I don't want to weld them on
No probs. Please still do a sideways pic as i may be able to extend your mounts without having to weld. I have so many bits and pieces that i may have a piece that would just slide in between the mount and light bracket.

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 6:56 pm
by Stu
I will do when I get 5 mins :thumb:

Re: Auxiliary light brackets

Posted: Fri May 12, 2023 10:15 pm
by Stu
@Doctor T

As requested

Needs a bloody wash :lol:

Re: Auxiliary light brackets

Posted: Sun May 14, 2023 6:34 pm
by Doctor T
I see now. There's not much movement or anywhere else to mount them. I will say my highway pegs are fitted lower and ive never got anywhere hitting the going around corners. Personally, i would move the spot mounts lower down near the downpipes and then they would be tucked in more and out of the way