Page 1 of 1
Timing Cover - Screws & Washers
Posted: Wed Apr 22, 2015 8:31 am
by David.
I'd like to replace the original (now corroded after 3 years) Timing Cover Screws & Washers on my 2012 Twin Cam RT.
The BMW Part No. is 07 12 9 905 537 & they cost £2.33 each x 12 = £27.96.
A trip to Hawk Fasteners in Middlesbrough came up with some Stainless Steel M6 x 30 Socket Head Cap Screws & Washers (12 off) for £6.21.
If you have changed any screws or fixings etc. for Stainless Steel, where did you get them from, thanks.
Re: Timing Cover - Screws & Washers
Posted: Wed Apr 22, 2015 8:41 am
by stelyn
David, I did the same as you changed the existing ones with stainless steel bolts which are easy to `undo' , got mine at Screwfix, ....... 
Re: Timing Cover - Screws & Washers
Posted: Wed Apr 22, 2015 1:56 pm
by stelyn
Complete Sets by Bristol Super Bikes, £9.99 see Link; :whistle:
http://www.ebay.co.uk/itm/BMW-R1200GS-R ... 27fcfe4934
Re: Timing Cover - Screws & Washers
Posted: Wed Apr 22, 2015 6:22 pm
by David.
Cheers Steve, the Allen Headed Screws with separate Washers look the same as the ones I have already purchased.
The smaller Screws in the ebay link will be for the plastic Alternator Belt Cover & Beltguard, M5 x 16 (7 off).
Re: Timing Cover - Screws & Washers
Posted: Thu Apr 23, 2015 5:28 pm
by David.
Bought (7 off) M5 x 16 Stainless Steel Screws today for £1.
Removed one of each M5 x 16 & M6 x 30 Bolts to check the sizes including the Washers, they fit perfectly.
Better quality than BMW OE at a fraction of the cost.
Re: Timing Cover - Screws & Washers
Posted: Thu Apr 23, 2015 5:55 pm
by stelyn
£1 - That's even cheaper, where did you get them ?
Re: Timing Cover - Screws & Washers
Posted: Thu Apr 23, 2015 6:38 pm
by David.
Teesside Industrial Fasteners,
http://www.tsidefasteners.co.uk/.
The BMW OE M5 x 16 Screws cost $0.96 each, (approx. £0.64).
Re: Timing Cover - Screws & Washers
Posted: Thu Apr 23, 2015 9:53 pm
by Steveeung
Couple of questions... Does anyone know where you can get these for the LC (stock ones are cheap looking)? Also what torque setting should they be tightened to?
Re: Timing Cover - Screws & Washers
Posted: Thu Apr 23, 2015 10:15 pm
by David.
Looks like this is the Front cover / oil tank on an LC,
http://www.realoem.com/bmw/showparts.do ... g=11&fg=14.
The Screws are M6 x 20mm (16 off), available from Amazon,
http://www.amazon.co.uk/Socket-Bolts-St ... B00A76IKCC.
Don't forget the Washers,
http://www.amazon.co.uk/Washer-Stainles ... DWMCCRZG7J.
The Torque setting on a
Twin Cam is 9Nm, (Bolt size is M6 x 30mm).
It's worth noting that A2 Stainless Steel is not the same grade or quality as A4, but still better than BMW OE.
I was initially offered some A2 Screws but the finish on the heads was poor, (could have been a faulty batch).
The guy in the store suggested using A4 at twice the cost.
Re: Timing Cover - Screws & Washers
Posted: Fri Apr 24, 2015 4:25 pm
by David.
Looks like to complete the job on a
Twin Cam, you need some screws for the two Fairing Brackets which bolt to the Stud Bolts on the Timing Cover.
http://www.realoem.com/bmw/showparts.do ... g=46&fg=63
Item No. 03, Screw & Washer M6 x 45mm (1 off), plus Item No. 06, Oval-head Screw M6 x 16mm (2 off).