Page 1 of 3

Dealing with corrosion!

Posted: Sun Jan 08, 2023 5:58 pm
by Stu
While the bike was on the ramp I noticed that the left throttle body was pretty badly corroded in a couple of places
20221229_205847.jpg
20221229_205847.jpg (304.6 KiB) Viewed 1274 times
20221229_205921.jpg
20221229_205921.jpg (394.8 KiB) Viewed 1274 times
And to be Honest looking at it I think someone has had a go at it before

I took the plunge and removed it and removed all the lose flaking paint gave it a sand to rough it up masked it up and gave it 4 coats of black hammarite smooth

And to be honest I am pretty impressed with the result! the paint is a very good match to the original
20230102_155016.jpg
20230102_155016.jpg (418.83 KiB) Viewed 1274 times
20230102_155010.jpg
20230102_155010.jpg (325.11 KiB) Viewed 1274 times
20230107_154808.jpg
20230107_154808.jpg (322.5 KiB) Viewed 1274 times
20230107_174405.jpg
20230107_174405.jpg (383.55 KiB) Viewed 1274 times
20230108_113304.jpg
20230108_113304.jpg (377.89 KiB) Viewed 1274 times
20230108_121514.jpg
20230108_121514.jpg (341.06 KiB) Viewed 1274 times
While I was at it I also stripped the spot light brackets as they was showing signs of rust showing through

I was also pleased with the outcome of those too
20230108_113500.jpg
20230108_113500.jpg (299.52 KiB) Viewed 1274 times
20230107_174310.jpg
20230107_174310.jpg (343.4 KiB) Viewed 1274 times

Re: Dealing with corrosion!

Posted: Sun Jan 08, 2023 7:10 pm
by simbo
Looks good :thumb:

Re: Dealing with corrosion!

Posted: Sun Jan 08, 2023 7:18 pm
by Stu
simbo wrote: Sun Jan 08, 2023 7:10 pm Looks good :thumb:
Cheers

Not that its going to matter as you can't see them with the fairing on but I know its done :lol:

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 8:08 am
by Panman40
sakm wrote: Sun Jan 08, 2023 5:58 pm While the bike was on the ramp I noticed that the left throttle body was pretty badly corroded in a couple of places

20221229_205847.jpg

20221229_205921.jpg

And to be Honest looking at it I think someone has had a go at it before

I took the plunge and removed it and removed all the lose flaking paint gave it a sand to rough it up masked it up and gave it 4 coats of black hammarite smooth

And to be honest I am pretty impressed with the result! the paint is a very good match to the original

20230102_155016.jpg

20230102_155010.jpg

20230107_154808.jpg

20230107_174405.jpg

20230108_113304.jpg

20230108_121514.jpg

While I was at it I also stripped the spot light brackets as they was showing signs of rust showing through

I was also pleased with the outcome of those too

20230108_113500.jpg

20230107_174310.jpg
Nice job looks professional!, my 2019 has the scab on the right TB , I was going to try and remove my centre stand for powder coating but I might spray it now.

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 9:09 am
by Stu
Panman40 wrote: Tue Jan 10, 2023 8:08 am Nice job looks professional!, my 2019 has the scab on the right TB , I was going to try and remove my centre stand for powder coating but I might spray it now.
My centre stand is on the list to get a tidy up too

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 4:45 pm
by Panman40
sakm wrote: Tue Jan 10, 2023 9:09 am My centre stand is on the list to get a tidy up too
Those springs look pretty tough to disengage… tempting to use brush hammerite :lol:

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 6:14 pm
by Stu
Panman40 wrote: Tue Jan 10, 2023 4:45 pm Those springs look pretty tough to disengage… tempting to use brush hammerite :lol:
Yes I agree! But at least they have something you can use the pull the springs

Others I have removed have just the spring ;)

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 6:41 pm
by simbo
sakm wrote: Tue Jan 10, 2023 6:14 pm Yes I agree! But at least they have something you can use the pull the springs

Others I have removed have just the spring ;)
Put the bike on the centre stand and place washers between the gaps in the spring, push the bike off the stand and the spring stays extended and easier to remove. Repaint the stand then reverse the procedure. :thumb:

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 7:05 pm
by David.
This is how Normski did it on a GS.


Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 7:12 pm
by Stu
David. wrote: Tue Jan 10, 2023 7:05 pm This is how Normski did it on a GS.

Its different on the RT There is actually something to use as leverage too

But that way looks a cracking idea :thumb:

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 7:16 pm
by David.
sakm wrote: Tue Jan 10, 2023 7:12 pmIts different on the RT.
Is it like this.

Image

If so, this should do the trick.


Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 7:34 pm
by Stu
Yes thats the one @David. :thumb:

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 7:37 pm
by burridge01
Never had trouble removing a spring using one of these
Image
Although I've never used the washers for spacers,that is 1 I shall remember and use in the future :thumb:

Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 7:44 pm
by David.
Here's another idea using a ratchet strap, fast forward to 9:00.


Re: Dealing with corrosion!

Posted: Tue Jan 10, 2023 7:54 pm
by Stu
burridge01 wrote: Tue Jan 10, 2023 7:37 pm Never had trouble removing a spring using one of these
Image
Although I've never used the washers for spacers,that is 1 I shall remember and use in the future :thumb:
Thats what I was planning on using :)